The Vision bypass allows operating small loads on Z-Wave controlled 2-wire dimmers.
In the two-wire system the electronics of the dimmer or switch is powered by one wire coming from the mains supply plus one wire that comes from the load itself.
This means that even when the load is turned off a small current runs through the load in order to power the Z-Wave electronic. This small current can cause a small load (e.g. a LED bulb with only 9 W) to flicker even when powered off. This flickering will also impact the dimming.

This sensor detects any vibration or shock of the device it is mounted to. It can therefore be used to protect any valuable goods, windows, doors or any other kind of gear that is not supposed to move or vibrate. The sensor has a manual calibration and adjustment element to adapt the sensitivity to the different applications. The installation can be done with screws or double-sided tape.

The device is battery-operated and therefore in sleeping mode unless an action is detected. After a programmable sleeping time the device wakes up and sends a status information. After this the unit goes back to sleeping modus. Batteries can be changed without unscrewing the device from the door or frame. The unit will give a visual warning on the device and sends a warning to the Z-Wave controller, when batteries need to be replaced. The CR123 Lithium battery lasts 3 ... 5 years in normal operation conditions.

The units send information to a controller or any other associated Z-Wave device. Up to 5 devices can be controlled from this device.

A tamper switch protects the device from removal or manipulation if used in security applications.

Two terminals allows to connection of an external dry contact in parallel to the vibration sensor.

This motion detector (PIR = passive infrared receiver) detects the presence of a person in a room. The units send information to a controller or any other associated Z-Wave device.
Up to 4 devices can be controlled from this device.
Beside the motion detector function the device also works as temperature sensor.
The installation can be done with screws or double-sided tape.
The device is battery-operated and therefore in sleeping mode unless an action is detected. After a programmable sleeping time the device wakes up and sends a status information. After this the unit goes back to sleeping modus.
Batteries can be changed without unscrewing the device from the door or frame. The unit will give a visual warning on the device and sends a warning to the Z-Wave controller, when batteries need to be replaced.
A tamper switch protects the device from removal or manipulation if used in security applications.
The powerful CR123 Lithium battery lasts 3 ... 5 years on normal operation conditions. The device supports normal Z-Wave inclusion, auto inclusion and network wide inclusion for convenient handling.

This Smoke Detector uses a non-radioactive photoelectron-sensor for a reliable and safe detection of smoke. The smoke sensitivity is 0.5 % /ft … 4 % /ft. The smoke detector has a test button and a flashing led, so you always know that the smoke alarm is working correctly.
The smoke alarm will warn you when the battery is low. When the device detects smoke, it will give a loud warning sound. It will also trigger actions in other Z-Wave devices or Z-Wave controllers to escalate the alarm.
The Smoke Detector can also activate an alarm-scenario within the Z-Wave network. For example you can create an alarm-scenario to switch on all lights in the house when smoke is detected. Even at the middle of the night, you may leave the house very quickly when smoke is detected.

The ZM 1702 is a Z-Wave controllable door lock that fits into standard European doors. The mechanics can be adopted to right or left opening doors.
The door lock can be applied for doors from a thickness of 38 mm and up. Since the lock is just a single dead bold lock it will not replace modern three dead bold locking outer doors.
The door can be locked and unlocked using the inner side turn piece and/or the key pad. The wireless control allows to lock/unlock the lock, set/unset up to 15 different key codes (4...8 key long) and to limit the validity of certain key code.

The ZM1701 is a Z-Wave controllable door lock that fits into standard European doors.

The door lock can be applied for doors from a thickness of 38 mm and up. Since the lock is just a single dead bold lock it will not replace modern three dead bold locking outer doors.

The door can be locked and unlocked using the inner side turn piece and/or the key pad. The wireless control allows to lock/unlock the lock, set/unset up to 15 different key codes (4...8 key long) and to limit the validity of certain key code.

he Vision USB-Stick is a Z-Wave USB dongle. When attached to a host processor, it becomes a Z-Wave communication device, which exposes the Zensys API (SerialAPI) through integrated USB. The primary function of the device is to allow a host processor to control up to 232 Z-Wave devices using the Z-Wave technology protocol. Within the Z-Wave wireless network the Z-Stick acts as a static controller with enhanced (SUC/SIS) network management function. In order to use the full functionality a software application such as Z-Cloud or Z-Way is needed to run on the host. Z-Stick supports all kinds of third party software complying with the Zensys Serial API.

The siren will warn everybody in the building by a loud sound and a flashing light about an alarm. This product is especially suited for security applications in combination with other Z-Wave devices such as door or windows sensors or motion detectors. The siren gives a loud sound and a flashing warning light, so everybody in the building will know immediately that an alarm has occurred. The noise level fo the siren is > 105 dB in range of 1 meter. The device can be configured to either use the strobe flash or the acoustic siren or both. A tamper switch protects the device from removal or manipulation if used in security applications. The device is battery powered.

The siren will warn everybody in the building by a loud sound and a flashing light about an alarm. This product is especially suited for security applications in combination with other Z-Wave devices such as door or windows sensors or motion detectors.
The siren gives a loud sound and a flashing warning light, so everybody in the building will know immediately that an alarm has occurred.
The noise level fo the siren is > 105 dB in range of 1 meter.
The device can be configured to either use the strobe flash or the acoustic siren or both.
A tamper switch protects the device from removal or manipulation if used in security applications.
The device is mains powered but has a backup battery inside to remain in operation in case of a power outage.