Flush shutter DC module with inverting power polarity is used to control the 12-24VDC motor of blinds, rollers, shades, venetian blinds, windows, etc.

New functionality - support venetian blind slats tilting

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

This module is used for switching On or Off 1 electrical device like light, fan, oven, washing machine, iron, power socket, garage door, electric radiator, water heater, etc.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

This module is used for switching On or Off 1 electrical device like light, fan, oven, washing machine, iron, power socket, garage door, electric radiator, water heater, etc.

With this module can feed your load with the desired voltage because it has a separate entrance for this purpose.
item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

The Qubino On/Off Thermostat 2 is your wireless heating and hot water controller that also measures the power consumption. This amazingly tiny module is ideal for wireless control of electric or water-based underfloor heating systems, electric water heaters, hot water pumps, and electric radiators.

Smart wallplug with consumption measurement. The smallest 16A Z-Wave plug on the market. With Z-Wave Plus technology and consumption measurement. It does not limit the power of the plug to which we connect the smart plug since these are usually 16 amps, like this SmartPlug 16A of Qubino.

This Z-Wave module is used for energy measurements in single-phase electrical power network till 65A. Meters measure energy directly in 2-wire networks according to the principle of fast sampling of voltage and current signals. A built-in microprocessor calculates energy, power and power factor from the measured signals.

The module can be controlled through Z-wave network and it acts as repeater in order to improve range and stability of Z-wave network.

It is designed to be mounted on DIN rail.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

The Qubino three-phase smart meter can be used in many automation scenarios that make your life more comfortable. Smart Meter is an extremely versatile and powerful instrument for measuring energy in a three-phase power network up to 65A. A built-in microprocessor calculates the power, reactive power and power factor with the measured values. The smart meter is designed to be mounted on a DIN channel. The Qubino Smart Meter can be used in residential, industrial and commercial facilities. This equipment permanently measures the current and voltage in a three-phase network. Calculate the current and total power, the PHI power factor and the reactive energy that is actually consumed. The control through Z-Wave allows to act the relays (available separately), as well as to evaluate the results of the measurements of the device. With the energy data we can carry out the most varied actions, such as being alerted if the consumption exceeds a certain limit, sliding loads to keep the consumption below a certain level, etc.

to work with ZWGOA ZMNHTD1 Smart Meter
wired connection
Voltage: 230V ± 10%, 50-60Hz
Current: 32A, 2 pole

to work with ZWGOA ZMNHTD1 Smart Meter
Infra-red connection
Voltage: 230V ± 10%, 50-60Hz
Current: 32A, 4 pole

Temperature sensor can be installed inside this Wall mounted casing. The dimensions of the Wall mounted casing are 71mm x 71mm x 27mm. This casings are made from ABS material and are available in white colour.

Temperature sensor can be installed behind this 2M casing SET. It is suitable for mounting on boxes Ø60 with claws. SET consists of: 1 x cover plate1, 2 x 1M perforated blank cover and 1 x mounting frame 2M with claws. 2M casing SET is made of PC/ABS material and comes in 2M dimensions. 2M casing set is available in polar white colour.

Digital Temperature sensor has 1m cable with connector to connect directly to the different modules. The digital temperature sensor range is between -50°C and +125°C.

SPU-DIM-C02 can control single colour LED strips from a standard push switch or from a 0-10V or 1-10V from any manufacturer. The controller can be connected to one or more push switches (check wiring diagram) or with 0-10V or 1-10V signals

Qubino Shades Remote Controller is 9 Channel Z-Wave standard handheld product. The World‘s 1st Z-Wave remote for shades control (Z-Wave secondary controller).

The Aeotec Smart Switch 6 is an intelligent remote controllable adapter plug which can control and monitor any electrical device. Due to its energy measurement function, you can identify all power eater in your home.

With the AEOTEC Dual Nano Switch all switchable and non-dimmable electric installations (e.g. lighting, sockets...) can be integrated into a Z-Wave network. Thus, the connected load can be switched both wirelessly via Z-Wave and locally via existing wall switch.

The compact radio module (60% smaller than its predecessor Micro Smart Switch) is placed in a wall box right behind the normal switch. The switch is no longer directly connected to the load but acts as input device for the AEOTEC insert that is controlling the load. The switch only sends control signal to the insert which controls the load then again. The solution works with all switch design. You can use a momentary or a toggle switch. It’s recommended to use wall boxes with 65mm depth. But smaller boxes with only 45mm depth can be used also if there is enough space behind the switch. The available space depends on the size of the traditional switch, the dimensions of the wall box and the amount of additional cabling placed in this box.

Additionally, the ZW132 has an integrated power metering function which allows to detect the exact energy consumption of the connected load.

The AEOTEC Nano Dimmer is a flush-mounted radio module which turns a standard light installation into an intelligent smart home component with Z-Wave wireless technology.

The compact radio module is placed in a wall box right behind the normal switch. The switch is no longer directly connected to the load but acts as input device for the AEOTEC insert that is controlling the load. The switch only sends control signal to the insert which controls (switch/dim) the load then again. The solution works with all switch design. You can use a momentary or a toggle switch. It’s recommended to use wall boxes with 65mm depth. But smaller boxes with only 45mm depth can be used also if there is enough space behind the switch. The available space depends on the size of the traditional switch, the dimensions of the wall box and the amount of additional cabling placed in this box.

Close your motorized windows automatically if it starts raining or shut down your shades if it is to warm outside. The Aeotec Nano Shutter enables you to control a broad selection of devices wirelessly and intelligently. The module equips motors for shutters, shades, garage doors, venetian blinds, etc. with Z-Wave technology. Thus, shutters and venetian blinds can be controlled both wirelessly via Z-Wave commands and locally via the connected conventional wall switch. The Aeotec Nano Shutter is designed to be mounted inside a flush mounting box, hidden behind a conventional wall switch.

The Aeon Labs Smart Energy Switch Micro is a low-cost Z-Wave appliance switch specifically used to enable Z-Wave command and control (on/off) for existing in-wall switches. The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.

The Aeon Labs Smart Energy Switch Micro is a low-cost Z-Wave appliance switch specifically used to enable Z-Wave command and control (on/off) for existing in-wall switches. It can also report immediate wattage consumption or kWh energy usage over a period of time. The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.

The Aeon Labs Micro Energy Illuminator Micro is a Z-Wave light dimmer specifically used to enable Z- Wave command and control (on/off/dim) for existing in-wall dimmers. The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.

The Aeon Labs Micro Smart Energy Illuminator is a Z-Wave light dimmer specifically used to enable Z- Wave command and control (on/off/dim) for existing in-wall dimmers. It can also report immediate wattage consumption or kWh energy usage over a period of time. The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.

The Aeon Labs Heavy Duty Switch is used for wireless control, automate and record the power consumption of heavy loads up to 40 amps. The Device can be controlled by other Z-Wave devices and can switch his heavy loads. He also works as a repeater and can forward, if the respective device are in range, signals to other Devices.

With AEOTEC’s new and smart RGB bulb color comes into play. The Aeotec bulb fits into every E27 bulb holder and connects to a smart home center through Z-Wave wireless technology. It is able to vary brightness and light color as well. Daylight, candle light or party atmosphere: As of now you can define light atmosphere according to your wishes.
The bulb uses 15 different LED diodes to shine in perfect shading of natural white light. These 15 diodes confer light temperature of 2580-7050K on the LED bulb.

• Cold white: 4745K to 7050K;
• Natural white: 3710K to 4745 K;
• Warm white: 2580K to 3710K ;

Well-known manufacturers such as Samsung and Philips also use the same LED technology.
An additional row with diodes gives Aeotec’s bulb the opportunity to vary between 16 million colors.
Furthermore the bulb can be switched on and off time-controlled via defined scenes or by a motion sensor. Use your Aeotec bulb as notification or status LED. Installed in the corridor it could flash in red color if you want to leave your home and windows or terrace door are still open. Due to LED technology power consumption is very low compared to conventional bulbs. The Aeotec bulb is as bright as a conventional 70W bulb, but needs only 9W.

Smarter. Safest. Smaller still. Plug it. Automate it. Control it. Understand how much electricity you are spending. Smart Switch 7 is Aeotec's smallest smart plug and is also everyone's safest.

Intelligence is in control. Appliances turn on when needed and off when not. On a schedule. Or intelligently automated and triggered when needed. You are completely in control. It is smart because it can be automated. But it's also a smart plug because the power to turn it on or off manually is always yours.

In real time and with 99% accuracy, Smart Switch 7 will analyse appliances electricity consumption helping you save what you spend. Furthermore the Smart Switch 7 is one of the best in design and quality. European design, German engineering and SGS certfication make Smart Switch 7 the smallest and safest smart plug.

Recessed Door Sensor is a new small and compact Z-Wave sensor with the size of 2.5*7 cm (main body), that tells you and your Z-Wave network if a door is open or closed. It is nearly invisible, as the sensor is installed with the help of a slight drill hole hidden away on the top of your door. Installing Recessed Door Sensor is easy, as you only have to add it to your home’s network activating its battery and associating it with your Z-Wave system.

Motion for security. Motion for presence. Motion for management. The Aeotec MultiSensor 7 motion sensor is perfect for more than just an intelligent security system. With a 10 metre range and a 120° field of view, MultiSensor 7 captures motion data that can be used for everything from security to heating management to energy saving. Knowing if a room is occupied or a hall is being used is a powerful piece of data – MultiSensor 7 makes your home automation system more powerful and more intelligent.

With the ceiling mount called "Recessor" you can integrate the Aeotec multi sensor into the ceiling - almost invisible and effective. Analogous to integrated ceiling lamps the sensor disappears almost complete in the ceiling. Simultaneously the detection area for the multi sensor (i.a. motion and light intensity) is enlarged.

Description Every Z-Wave Smart Home depends on data for truly intelligent automation; automation that makes a Smart Home actually smart, responsive and secure. The Aeotec TriSensor provides your Smart Home with its most essential data. 3 different sensors are crafted into Aeotec TriSensor’s impossibly small finish. A motion sensor to monitor a room’s occupancy, a temperature sensor to manage its environment, and a light intensity sensor to manage connected lighting. At only 1.77 inches in size and weighing only 50 grams, Aeotec TriSensor is really small. That means it can be placed almost anywhere in your home. TriSensor offers 4 different installation possibilities: in the corner, on a shelf, beam or in the Aeotec Recessor. Features Motion Sensor The sensor detects motion in up to 7.5 meters distance. It can also be adjusted and calibrated to it needs, e.g. to avoid an alarm by a pet. Temperature The temperature sensor is accurate and detects temperatures in the range from -10°C to 50°C (+/- 1°C). The temperature can be used in connection with heating device. Furthermore the Aeotec TriSensor can control a directly associated device, if the temperature goes above a configured level. Light Measure the light intensity from 0 - 30000 Lux and automate your ambient light in depending on the daylight.

With the Water Sensor 6 of Aeotec you are protected against water damages. This device is already greatful but with the Water Sensor Dock it becomes more greatful.The installation of the dock offers several advantages to you.

The Aeotec Door/Window Sensor 7 is a sensor, which detects, if your window is opened, closed or tilted which requires a tilt angle of at least 5°. The sensor is easily retrofittable. Furthermore, the Aeotec Door/Window Sensor 7 can include other sensors by being connected with other binary sensors like NTC contacts, micro switches or flood sensor. Thanks to its slim design the Aeotec Door/Window Sensor 7 can be installed unflashy on every window. The sensor just has to be installed on the window casement. Additionally, there has to be a slim magnet installed closely to the sensor at the window frame.

The Aeotec Water Sensor 7 Pro is a flood sensor, a leak sensor and a safety sensor in one device.

The Aeotec Water Sensor 7 is a flood sensor, a leak sensor and a safety sensor in one device.

The Aeotec Door Window Sensor 7 Pro is a sensor which detects if your window is opened, closed, or tilted which requires a tilt angle of at least 5°.

Run your smart home locally, privately, and cloud-free. Aeotec Z-Stick 7 lets you build your own automation gateway using Gen7 and 700 series Z-Wave technologies.
Brimming with new features and technology, yet wholly more compact. Z-Stick 7 is 79% smaller than Z-Stick Gen5+ and yet it is still just as easy to setup.

With the new Z-Wave USB Stick Generation 5 by Aeon Labs your PC, notebook, Barebone, Raspberry Pi etc. change into a central controller of your smart home.

The control of the Z-Wave network is realized via "Z-Wave Serial API" (according to "Z-Wave Application Programmers Guide, INS10247"). It‘s also used by well-known Z-Wave control programs such as IP Symcon, Homeseer etc. This allows you to use the USB stick GEN5 universal with other Z-Wave software solutions. Thanks to the integrated battery, you can also include or exclude any devices in your Z-Wave network by pushing on the local button, when PC or Notebook is turned off.

Aeotec's WallMote is a remote control, wall switch and Z-Wave controller, all-in-one. This device can manage its own Z-Wave network (if included as a primary controller) and can control other devices such as sockets, blinds, dimmers, lights, electronic locks and many more. Obviously, it can also be integrated into a Z-Wave network as a secondary controller. WallMote is the perfect Z-Wave controller. Wireless, battery powered, but capable of controlling hundreds of devices in more than a dozen Z-Wave scenarios.

Aeotec’s Z-Wave Plus repeater and range extender.

Pack of 2 x Aeotec’s Z-Wave Plus repeater and range extender.

The Aeotec Siren 6 makes your home smarter and safer. The Aeotec Siren 6 enriches your Smart Home with a further safety factor. In combination with other Z-Wave devices, the visually appealing alarm siren warns of various situations with acoustic (110db) and visual signals. Whether water escapes in the cellar, smoke develops in the kitchen or an open door at night, the siren draws your attention to all these conspicuous features. You can also use the siren as a doorbell in addition to the alarm functions. The Aeotec Siren 6 plays 30 different tones, which are defined via parameters in the gateway. In summary, this device works particularly well for any type of acoustic and visual alarm in your Smart Home. The power supply of the Aeotec Siren 6 works easily via a power socket or battery operated. Due to its high-quality design, the siren fits well into your rooms and is hardly noticed.

The Aeon Labs Smart Energy Monitor is a low-cost energy monitor for the entire home. It can wirelessly report immediate wattage and kWh usage to central control point gateways and can be easily and safely installed by anyone. Ease and safety are paramount: Electricians are not required to install the Aeon Labs Smart Energy Monitor; the customer never needs to handle hot exposed wiring. Current transformer clamps clamp around the AC Mains to detect energy usage for the entire house.
The main body is anchored using a back mount. The device has three clamps and reports W, kWH, V and A (up to 60 Ampere).

You want to design your home smart and are looking for a suitable starter package? Smart Home is a term to you, but you have questions about the selection of products? Then we have the solution for you here. With the Aeotec SmartThings Starter Kit you get an perfect all-round package for getting started in the smart home world.

The Aeon Labs Smart Energy Monitor is a low-cost energy monitor for the entire home. It can wirelessly report immediate wattage and kWh usage to central control point gateways and can be easily and safely installed by anyone.
Ease and safety are paramount: Electricians are not required to install the Aeon Labs Smart Energy Monitor; the customer never needs to handle hot exposed wiring. Current transformer clamps clamp around the AC Mains to detect energy usage for the entire house. The main body is anchored using a back mount which opens to easily. The device reports W and kWH.

One look and you are home. With the Aeotec Cam 360, you get a 360 degree view of your room at a glance. Display a detailed view of what's going on at home at day or night. Communicate through 2-way audio and a built-in microphone via the SmartThings App. Receive alerts when motion or sound is detected. Customize detection zone to pay closer attention to specific areas for unexpected activity. Use SmartThings App to automate scenes and routines with compatible smart devices.

Aeotec Nano Dimmer Bypass for use with Aeotec Nano Dimmer has been designed to stop most bulbs from flickering including static and dimmable LEDs and CFLs.

The Philio Insert Switch allows controlling two independent loads both wirelessly via Z-Wave and locally utilizing a traditional wall switch. Thanks to its calibration technology the PAN06 cannot only be used to switch AC devices ON and OFF, it also works perfectly with many kind of light, e.g. incandescent, fluorescent and LEDs.
In addition to this, the PAN06 can be connected to 12V/DC, which makes it possible to switch 12V MR-16 light as well.
The device is placed in a wall box right behind the normal switch. The switch is not longer directly connected to the load but acts as input device for the insert that is controlling the load.
This device is designed for a 3 wire system and needs a neutral wire in the wall box.

Heatit Z-TRM3 is an electronic thermostat for electrical floor heating, designed to be mounted in a standard flush box. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems. Heatit Z-TRM3 has SmartStart. This feature allows the user to include all devices with SmartStart by scanning the QR codes on the devices. On startup all the devices will automatically be included in the gateway (requires SmartStart compability). This saves the installer a lot of work.

Art. 54 305 99

This in-wall dual relay switch module is a transceiver which is a Z-Wave Plus enabled device and is fully compatible with any Z-Wave enabled network.Mini size design let the module can easily hide itself into the wall box and that will be good for the house decoration. There are many kind of application by using the module to switch AC power On and Off, one main application is the light control. The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light.This in-wall switch module is able to detect Instant power wattage and overload current (7.5A) of connected light or appliances. When detecting overload state, the Module will be disabled and its On/Off button will be lockout of which LED will flash quickly. However, disconnect and re-connect the Module will reset its overload condition to normal status.

The Philio Roller Shutter Controller insert allows controlling motors for jalousies and blinds both via Z-Wave wirelessly and locally utilizing a traditional wall switch.
The device is placed in a wall box right behind the normal switch. The switch is not longer directly connected to the load but acts as input device for the Philio insert that is controlling the load.
This relay is able to detect the position of the shutter by using the patterned power measuring method. So it can be remote controlled not only fully up or down, but also can be adjusted to e.g. 30% or 50%. And when manual controlled by using the push button, the controller also can memorize the position and send the new shutter position to its controller (ex. IP-Gateway).
The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of roller shutter.

Transform any home into a smart home with the Philio PAD02 Z-Wave Smart Dimmer Socket. The dimmer socket can be easily adapted to your current lighting devices, uses your existing lamp (E27 socket), and provides Z-Wave wireless and with remote control of overhead lighting. Use the dimmer feature to customize the lighting output and create the perfect ambiance for any room. Providing ultimate flexibility, the Philio Z-Wave Smart Dimmer Socket allows you to operate the lighting by itself or easily integrate the socket with two-way, three-way or four-way wiring configurations by adding the Philio Smart Switch Modules for Z-Wave. Take control of your home lighting with Philio Z-Wave Smart Lighting Controls!
Easily adapt to any standard lamp E27 socket with the Philio Z-Wave Smart Dimmer Socket to turn lighting on/off or adjust dim levels with your mobile device or computer using any Z-Wave certified gateway. Can be controlled in groups of multiple lights or used to create dimmable ambient interior lighting scenes.

Heatit Z-Temp2 is a temperature sensor designed for use with waterbased heating systems. Using it in combination with the Heatit Z-Water regulator allows for an advanced waterbased heating solution that can be managed from a Z-Wave gateway.
This is a “wire-free” solution, saving both time and money. All communication between the Heatit Z-Temp2 and the controlled device is 100% wireless. Heatit Z-Temp2 has SmartStart. This feature allows the user to include all devices with SmartStart by scanning the QR codes on the devices. On startup all the devices will automatically be included in the gateway (requires SmartStart compability). This saves the installer a lot of work.

art. 45 126 66

Heatit WiFi is an electronic thermostat for electrical underfloor heating. The thermostat has a simple user interface and can be easily programmed via the capacitive buttons. The thermostat has an easy user interface.

The Z-Wave 3 in 1 sensor (PHI_PSM01) is designed with three detection sensors:

• Door/windows;
• Temperature sensor;
• Luminosity sensor.

The sensor consists of two parts; a Detector and a Magnet. They are designed to be fitted to doors or windows with the Magnet mounted on the opening part and the Detector mounted on the fixed frame. Opening the protected door/window will remove the magnetic field, trigger the detector and generate an alarm condition, (if the system is armed). The sensor can also applied to automatic light control, one scenario is to get the illumination lux level from built in illumination sensors and send a signal to Z-wave switch to turn the light on once we open the door when the room is dark.
Every time when Door/Window trig, the sensor will also send temperature and illumination value as well. Also the temperature will send out the value when temperature changes. Note: The illumination sensor yet does not work with Fibaro Homecenter 2 and Zipato Zipabox.

The Z-Wave 3 in 1 sensor (ZWphiPST02-1B) is designed with three detection sensors:

• PIR/Motion;
• Temperature sensor;
• Luminosity sensor.

The detector can be used as a security device or home automation device. When the detector is cooperated with security appliances, the detector is acting as a security device by detecting changes in infra-red radiation levels. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted to cause full alarm condition in order to frighten intruders away. Alternatively, when the detector is worked with Z-Wave Controller, the detector can be set to perform the role of home automation device by detecting both changes in infra-red radiation levels and percentage of lux levels.
Every time when PIR trig, the sensor will also send temperature and illumination value as well. Also the temperature will send out the value when temperature changes. Note: The illumination sensor does not work with Fibaro Homecenter 2 and Zipabox yet.

The Z-Wave 4 in 1 sensor (ZWphiPST02-1A) is designed with three detection sensors:

• Door/window sensor;
• PIR/Motion;
• Temperature sensor;
• Luminosity sensor.

Thanks to this the PSM02 can be uses as a security device or home automation device, e.g. to send an alarm when a motion is detected, turn the light on/ off automatically at night or to adjust the heater.
The product consists of two elements - the detector and the magnet. The magnet is mounted on the moving part of the window or of the door. The other part is placed on the frame.
Note: The illumination sensor does not work with Fibaro Homecenter 2 and Zipabox yet.

Zipato Flood Multisensor 3 in 1 integrates flood, temperature and humidity sensors in one device. Zipato Flood Multisensor 3 in 1 offers elaborate security and ambient sensing options. Multifunctional nature of this product allows you to informed about water leakages and potential flood disasters, as well as to measure temperature and humidity levels. When used with Zipato home automation controllers it can be part of any automation scenario created using Zipato Rule Creator. Accordingly it can be used to automatically trigger other Z-Wave devices when activated.

The new Philio Motion Detector in small ball design detects movements at a distance of up to 12 meters. The sensor can be easily installed on the ceiling or a wall thanks to a supplied magnetic holder. Thanks to the unique and descretely design, you can place the sensor anywhere to automate your light. Then your light switches on only when the movement is detected, and if there is no person in the room, the lamps are not switched on.

The sensor also includes a lens cover. With the cover, you can hide an area which is not to be detected by the motion detector.

In addition, the sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside. The sensor is battery operated and can be easily added to your Z-Wave Smart Home System.

The compact sensor in ball design recognizes motion in a distance up to 12 meters and can be installed quite easily and individually at ceilings or walls.
This allows you to place the sensor descretely next to your lighting and automate your lights.

In addition, the sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside. The sensor is battery operated and can be easily added to your Z-Wave Smart Home System.

The compact sensor in ball design recognizes motion in a distance up to 12 meters and can be installed quite easily and individually at ceilings or walls.
This allows you to place the sensor descretely next to your lighting and automate your lights.

In addition, the sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside. The sensor is battery operated and can be easily added to your Z-Wave Smart Home System.

The Philio Round Recessor is made to mount motion sensors on the ceiling. The Fibaro motion sensor and the Philio outdoor motion sensor fit perfectly into the brackets. So the motion sensor is installed in the right position and through a firm and reliable attachment.

The Philio Square Recessor is made to mount motion sensors on the ceiling. The Fibaro motion sensor and the Philio outdoor motion sensor fit perfectly into the brackets. So the motion sensor is installed in the right position and through a firm and reliable attachment.

Philio’s „Smart Color Button“ is a real multi-talent. Use it as a remote control or switch your devices on and off. Turning right or left changes room temperature, drives shutters up and down or dims the light. The smart button gives a feedback to the last action with its colored LED ring.

Put your Philio Color Button to the refrigerator or heaters. Its backside is magnetic and sticks on metallic surfaces.

The Color Button can be connected to all relevant Z-Wave gateways (as secondary controller) and controls all devices within your intelligent Z-Wave network.

The Philio Smart Keypad with an elegant glass touch panel can be included in your Z-Wave network to increase the security in your home. The smart device support Z-Wave Multi-Functions Smart Switch to report the current key status and setup Arm/ Disarm.

Valid for the references: ZWPHI PAN08 - Z-Wave Plus Relay Insert Blind ZWPHI PAN06 - Z-Wave Plus 2 Relays Insert Refer in the observations field the desired quantities and references.

Heatit Z-Water is a DIN-rail regulator for controlling hydronic heating. The module clips right onto a DIN-rail to add a variety of functions to your wireless Z-Wave network. Heatit Z-Water is equipped with 10 relay outputs and it has 4 analog/digital inputs. The module is power supplied from a 230V AC mains connection and is able to deliver an output supply of 24V DC or 230V.

Heatit Z-Water relay outputs may be freely controlled from the Z-Wave network, and may be used for several purposes, e.g. on/ off control of lights, controlling valve actuators in an underfloor heating system, or controlling other home automation systems.

Heatit Z-Water analog/digital inputs (different firmware versions) may be configured to work with different functionalities. They may be connected to potential free contacts, opencollector outputs, and may also control other Z-Wave devices; switches, dimmers, etc. Furthermore, the inputs may be used as scene controllers and send central scene notifications to the Z-Wave primary controller (via digital inputs only).

Heatit Z-DIN 616 is a 6 x 16A potential free relays for DIN rail mounting. The module is equipped with 6 relay switches and 6 digital inputs for mounting on a standard M36 DIN rail (EN50022).

The 6 independent relay switches of the Heatit Z-DIN 616 can be freely controlled from the Z-Wave network and be used for many different purposes. All 6 relay switches are galvanically isolated from each other and may be used for controlling AC and/or DC loads. Each relay switch is rated for loads of up to a maximum of 16A.

The 6 digital inputs can be connected to dry contacts, e.g. limit switches, door/window contacts, or push-buttons. Another option is to connect them to open-collector outputs from discrete sensors, e.g. PIR sensors. The 6 inputs of the Heatit Z-DIN 616 may also function as a scene controller and activate predefined scenes in other Z-Wave devices or controllers (by transmitting Central Scene notifications).

The Heatit Z-DIN 616 is powered by a 10 – 24Vdc power supply. Initiation of Z-Wave inclusion and exclusion is executed by activating a push-button through a little hole in the front of the module. The Heatit Z-DIN 616 is equipped with a LED in the front of the module for different kinds of status indications.

Heatit Z-Relay multipurpose relay module can be used for many different applications. The IP 55 rated casing makes it useful for any outdoor application. Can pull loads up to 16A and 25A. The relay has three inputs: analog or digital. You can use both analog and digital inputs, or a combination.

Heatit Z-Relay is a multipurpose product and can be used for the following applications:
• Boiler control
• Leakage control
• Temperature control
• Outdoor applications
The relay has 3 analog/digital inputs and can be used with a lot of different sensors and meters, from water meter pulse sensors to NTC temperature sensors.
The relay comes in two different versions, 16A and 25A. They both have firmware updates (OTA), power metering and S2 security.
We are able to make special firmware if a customer has a special requirement.

Heatit ZM Thermostat has active power metering and it gives you real time information about your power consumption.

The Heatit ZM Single Relay has active power metering and it gives you real time information about your power consumption.

Heatit Z-Wave Gateway is a smart home control unit with a modern design. Heatit Z-Gateway has SmartStart. This feature allows the user to include all devices with SmartStart by scanning the QR codes on the devices. On start-up all the devices will automatically be included in the gateway. This saves the installer a lot of work.

This gateway allows you to control all Z-Wave devices in your home via tablet or mobile phone. The gateway is designed for easy setup and operation. With just a few clicks, you can easily add Z-Wave devices and create scenes. The settings are simple, but the possibilities are almost limitless.

Push notifications are supported, so you get notifications from your phone when an event is triggered in the smart home system, even when the phone is in sleep mode.

Voice control via Amazon Alexa and Google Home is also supported, and you can manage the system through voice commands. The gateway has support for IFTTT, which makes it possible to integrate the gateway with almost any smart device on the market, as long as they have IFTTT support.

The Heatit Z-Wave gateway gives you endless opportunities to tailor your smart home to your specific needs.

The Wall Controller is coin cell battery powered. The product is intended primarily for residential applications.

The Wall Controller is coin cell battery powered. The product is intended primarily for residential applications.

Heatit Z-Dim2 has active power metering and it gives you real time information about your power consumption.

Heatit Zig Dim is a ZigBee rotary dimmer for many different types of light fixtures.

Heatit Leakage Stopper can be used both outdoors and indoors, and is controlled through the Z-Wave network.

Heatit Z-HAN2 is a Z-Wave HAN sensor for AMS meters (Smart meters). Heatit Z-HAN2 works with HAN ports.

The Heatit Z-Smoke Multisensor is a multifunctional wireless smoke sensor for smart home systems. With its powerful features, the sensor is designed to protect the family from potential fire hazards. With its compact and streamlined design, the Heatit Z-Smoke Multisensor blends effortlessly with your home decor and gives you extra security.

The Heatit Z-Smoke Multisensor is a multifunctional smoke sensor for smart home systems. With its powerful features, the sensor is designed to protect the family from potential fire hazards. With its compact and streamlined design, the Heatit Z-Smoke Detector blends effortlessly with your home decor and gives you extra security.

Heatit External Room Sensor is designed for use with Multireg and Heatit thermostats. The sensor can be mounted directly on a wall or on top of a standard European wall box. It can be used with most frames that are adapted to System 55. The product comes in a matt version. When used with a thermostat, dimmer or other products that emit heat, it is recommended that the sensor be mounted below these other products. It is not possible to connect the sensors in series or in parallel.

Plastic frame for Multireg, Heatit Z-Wave and Heatit Z-TRM3.

Heatit HC frames are a frame system with space for one, two or three products. Frames for use with Heatit and Multireg products such as thermostats, dimmers and external sensors. Fits System 55 products.

Heatit HC frames are a frame system with space for one, two or three products. Frames for use with Heatit and Multireg products such as thermostats, dimmers and external sensors. Fits System 55 products.

Heatit Transformer is an in-wall transformer that fits European electrical wall boxes. It enables the user to connect low voltage devices to mains power and change the voltage from 230VAC to either 12VDC, 5VDC or 3.3VDC.

Heatit ZM Dimmer has active power metering and it gives you real time information about your power consumption.

Plastic kit for Heatit Z-Dim2 250W and Heatit eezedim 250W.

Plastic kit for Heatit thermostats. The plastic kit can be combined so that you can have a white frame and a black front, or vice versa.

The Heatit Z-Temp2 DC adapter allows you to connect the Heatit Z-Temp2 to the mains so that you are no longer dependent on batteries. Can also be used together with the Heatit Transformer to connect directly to the 230VAC mains.

NTC 10 kΩ @ 25°C Floor sensor for Heatit thermostats. Cable length 6 meters

NTC 10 kΩ @ 25°C Default sensor for Multireg and Heatit thermostats. Cable length 3 meters

Floor sensor designed for use with Multireg & Heatit thermostats.

The danalock V3 evolution is based on the feedback from devoted customers and the latest development in data security and smart home technology.
Smaller, stronger and easier to install the V3 takes the lead on the smartlock market and is setting new standards for years to come.

Setting New Standards:
Twice the power;
Four times faster;
Smarter, smaller and safer;
Auto calibration procedure;
Lock Status;

The danalock V3 evolution is based on the feedback from devoted customers and the latest development in data security and smart home technology.
Smaller, stronger and easier to install the V3 takes the lead on the smartlock market and is setting new standards for years to come.

Setting New Standards:
Twice the power;
Four times faster;
Smarter, smaller and safer;
Auto calibration procedure;
Lock Status;

The danalock V3 evolution is based on the feedback from devoted customers and the latest development in data security and smart home technology.
Smaller, stronger and easier to install the V3 takes the lead on the smartlock market and is setting new standards for years to come.

Setting New Standards:
Twice the power;
Four times faster;
Smarter, smaller and safer;
Auto calibration procedure;
Lock Status;

The danalock V3 evolution is based on the feedback from devoted customers and the latest development in data security and smart home technology.
Smaller, stronger and easier to install the V3 takes the lead on the smartlock market and is setting new standards for years to come.

Setting New Standards:
Twice the power;
Four times faster;
Smarter, smaller and safer;
Auto calibration procedure;
Lock Status;

The Danapad compatible with the Danalock V3, offers a secure access solution, easy to install and does not require a permanent modification of your door or entrance area. Simply install it within the Bluetooth range of your Danalock smart lock.

Operate Your Danalock from Anywhere! Connect your Danalock V3 smart lock to the Danabridge V3 and control and operate your Danalock from anywhere. Enjoy the added convenience of letting family members, friends and home service providers in – even when you’re not at home.

With the Danalock universal module you can conveniently control your garage door and motor-driven doors through your smartphone. The module has a relay to toggle a potential-free contact. The supply voltage can be output for a certain time (1-180 seconds) or permanent.

With the Danalock universal module you can conveniently control your garage door and motor-driven doors through your smartphone. The module has a relay to toggle a potential-free contact. The supply voltage can be output for a certain time (1-180 seconds) or permanent.

12 / 24V to 3V converter to operate the Universal Module V1.