alternativas: INS 2633-432 https://www.eurox10.com/pt/tomada-onoff-tipo-f-shucko

The Dimmer plug-in module is a 300W receiver unit that works as a remote dimmer.
The connected lamp can still be switched on and off locally. The dimmer function, however, is by an X10 remote control.
The dimmer module can be used at any wall outlet in the house with incandescent lamps between 40W and 300W. As the dimmer is simply inserted into wall outlets like an ordinary plug, there is no installation necessary. Just adjust the settings on the front side to the desired device address (e.g. F9) and note this address down in a list. The lamp connected to the dimmer module can still be controlled locally by its own switch, but do not forget to leave the local switch in the "ON" position, otherwise the lamp cannot be controlled by an X10 controller. Switch the lamp off by remote control.
The LM12E responds to STANDARD X10 protocols: "All lights on" or "All units off" from any X10 controller set to its house code, regardless of unit code. Or alternatively, by individual unit control using "On", "Off", "Bright" and "Dim".

The Wired Lamp Module is a small module that can be fitted easily in any false ceiling, wall, etc... to control your lights. The module can be installed directly into lighting fixtures. It can be built-in, wired to the light or lamp it has to controlled. Its small size allows you to fit this module almost anywhere. The perfect module when you want your X10 modules to be installed out of sight.

When an incandescent lamp is plugged onto this module, it can be controlled using any X10 controller or locally via the ON/OFF button on the module.
Simply press the ON/OFF button on the module to toggle between ON and OFF states or send an X10 command to it.
Using an X10 controller, this module can also respond to the X10 Bright/Dim command.

Equipo descontinuado
Alternativas:
AW12 + Caixa para calha DIN
INS_2453-422 Atuador On/Off para calha DIN

El X10 DIN rail interruptor es un relé de control remoto. Discretamente instalado en la caja de conexiones, cambia los circuitos cableados con varios interruptores de alumbrado (pasillo). El relé interno puede ser activado por interruptores de pared sea de enganche o acción momentánea o por un controlador X10.

El AD11 responde a los protocolos estándar de X10: "Todas las unidades off" desde cualquier controlador X10 establecido en su código de casa, independientemente del código de la unidad. O, alternativamente, la unidad de control individual mediante "On" y "Off". Cuando el relé está energizado, el LED situado encima del interruptor se ilumina.

The LW12 is an in-wall module with built-in dimmer that can be installed behind existing momentary switches or wall outlets.

The LW12 can be controlled with X10 signals via the mains or a momentary switch connected to the LW12. The LW12 has a memory setting for the last dimmer setting and uses SoftStart and SoftDim. The LW12 is the only X10 module that doesn't use a zero wire. This means it can replace a switch without having to use any extra wiring.

The AW 12 reacts to the standard X10 commands that are: "All Units On", "All Units Off", "All Lights Off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On" an "Off" commands.

House code and unit code are programmed using any X10 compatible controllers. There is an EEPROM that stores the house and unit code even when the power is cut.

Dimming actuator for installation behind retractive switches and wall sockets or in distribution boxes.
Suitable for remote or on-site operation of lighting.

Interruptor para insertar dentro de los cajetines de la instalación. Transforma un interruptor/pulsador convencional en un interruptor controlable X-10. Permite el control local y remoto del encendido y apagado de luces y aparatos.

Los micromódulos utilizan comunicación X10 y están diseñados para ser situados al fondo de los "cajetines de mecanismo", detrás de cualquier mecanismo de interruptor o enchufe.
El módulo responde al estándar X-10 las instrucciones individuales como:
"ON" (encendido) /
"OFF" (apagado) /
“All lights ON” /
“All lights OFF” /
“All Units OFF”
enviadas desde cualquier controlador X-10 que coincida con el código de casa del módulo.
El Micromódulo reconoce la acción de un pulsador o de de un interruptor. Todos los cierres de contacto momentáneo o continuo deben realizarse a la Fase.
Si se emplea un pulsador, el relé cambia de estado cada vez que se realiza una pulsación, siempre y cuando el tiempo del contacto dure menos de 2 segundos.
Si se emplea un conmutador, se asume que el tiempo de contacto tendrá una duración superior a 2 segundos. En este caso el relé cambia de estado al abrir el contacto (OFF) y al cerrarlo (ON). Este tipo de respuesta permitirá a la unidad realizar un control mediante “llaves conmutadas” si se dispone de dos conmutadores.
El AW12 usa comunicación x-10 de una sola vía.

he S2263M module allow to dim one lamp, being small enough (43 x 47 x 18,9 mm) to fit behind a wall switch or junction box. It allows to control both internal relay either using any conventional electric switch (push buttons are not supported) or remotely, using any X-10 compatible controller.

This module has a special feature which allows setting 16 distinct X-10 addresses to each internal relay. This is very useful to create macros.