• Door/windows;
• Temperature sensor;
• Luminosity sensor.

• PIR/Motion;
• Temperature sensor;
• Luminosity sensor.

• Door/window sensor;
• PIR/Motion;
• Temperature sensor;
• Luminosity sensor.

Philio’s „Smart Color Button“ is a real multi-talent. Use it as a remote control or switch your devices on and off. Turning right or left changes room temperature, drives shutters up and down or dims the light. The smart button gives a feedback to the last action with its colored LED ring.

Put your Philio Color Button to the refrigerator or heaters. Its backside is magnetic and sticks on metallic surfaces.

The Color Button can be connected to all relevant Z-Wave gateways (as secondary controller) and controls all devices within your intelligent Z-Wave network.

The MH-S411 is a glass-surface wireless actuator able to to switch 1 load up to 1100 W. It is designed for application in round Pattress boxes (according to PT, ES, DE, etc Standard).

Beside local switching the device can be used to control two groups of directly associated devices or scenes stored in the central controller.

A blue LED on the button indicates the switching status. The installation of the device requires a 3 wire system with neutral wire.

The MH-S412 is a glass-surface wireless actuator able to to switch 2 separate oads up to 1100 W. It is designed for application in round Pattress boxes (according to PT, ES, DE, etc Standard).

Beside local switching the device can be used to control two groups of directly associated devices or scenes stored in the central controller.

A blue LED on every button indicates the switching status. The installation of the device requires a 3 wire system with neutral wire.

The MH-S314 is a glass-surface wireless actuator able to to switch 4 separate oads up to 1100 W. It is designed for application in UK Pattress boxes (according to British Standard).

Beside local switching the device can be used to control four groups of directly associated devices or scenes stored in the central controller.

A blue LED on every button indicates the switching status. The installation of the device requires a 3 wire system with neutral wire.

The ZWS230 chain motor is thanks to its small dimensions and suitable force output ideal for roof window operating and is fully compatible with the Z-Wave system. The motor can be used to upgrade centre pivot and top hung and pivot roof windows of different manufacturers.

The maximum chain reach of the ZW230 is 36cm. The motor is equipped with built-in overload protection which acts as a sensor for correct window closing.

WiDom universal Double Switch is an ON/OFF control device designed to independently control two separate loads, suited for use as both a local and remote switch. Similar to the other WiDom “in wall” devices, it can be fully integrated into pre-existing systems and configured to link configurable behaviours to a specific number of clicks, in full interaction with the Z-Wave home automation ecosystem.

The WiDom universal Double Switch also boasts the lowest energy consumption on the market.

Energy Monitoring: Each of its two channels features an integrated consumption measurement device.

Timer Management: Timer management for each independent channel, both switch on and switch off.

Software Update: You will be able to independently update the device firmware "Over the Air" without even having to remove the devices from their location.

Extremely low energy usage: In line with the other WiDom products, the WiDom universal Double Switch features the lowest energy usage of all similar devices on the market.

Intelligent Multichannel: It has two independent channels individually controllable. It can independently control other devices both single channel and multi-channel. For example, you can remotely control the opening / closing of the shutters, to control of dimmable lights, turn on / off remote loads.

Not all Z-Wave devices support the associations and / or multi-channel associations. When associations are supported, typically are a simple local control reference (if I turn off the local light, I turn off also those associated). With Widom Universal Double Switch you can define the state of local load and the state of the devices associated independently of the load, and you can control them separately activating the recognition sequence of clicks. So you can check the local loads with single click, and the associated devices with double click.

Ready for installation, but fully configurable: The device is supplied ready for installation but can also be supplied with personalized configurations.

The Comet Z-Wave Thermostat heats your room right when you need it. So you do not have to enter a cold bathroom after waking up nor a cold home after coming home from work. In addition the thermostat lowers your heating and its costs.

Thanks to the Z-Wave wireless technology the Comet thermostat can be included into and controlled by your Z-Wave gateway. Set the room temperature from your smart phone: It does not matter if you are on your couch or on the way. Of course you can define scenes in your smart home gateway which regulate the temperature fully automatic.

As stand alone solution without a Z-Wave gateway you can program up to 6 times for heating or cooling per day. Thanks to “open window” detection the electric thermostat will stop heating as soon as you open the window to air the room and prevents you from throwing your money out of the window. Other functions like child protection, timer function, frost protection and many more can be activated over the menu-driven display.

The installation does not require any tools and can be performed without any further knowledge – dead easy!

Just take off the conventional thermostat and install the Comet. No need to drain water. Adapters for most common valves are enclosed in the package.

• the insert, which can be used with or without local control
• a special mounting plate to mount the insert into a pattress box
• a mounting frame for Duwi Everlux series , color standard white
• the switching paddle for local control of the dimmer

The NodOn® Soft Remote can control any kind of Z-Wave compliant receiver (standalone mode) such as the switchable plugs, blind controls and dimmers. In addition it is able to trigger scenes/actions via a Z-Wave compliant home automation gateway (gateway mode).

Spill and shock proof, the Soft Remote can be used anywhere in the house. Its embedded magnet allows to fix the Soft Remote everywhere, from the heater to the fridge door.

The TZ65-D dual wall dimmer is switching attached loads and is controlled either by the local switching paddle or remotely via the Z-Wave wireless protocol It is included and controlled in a Z-Wave network by a remote control, a wireless control centre or any other kind of Z-Wave controller including a PC-software.

Beside the local switch the unit can control other Z-Wave units remotely in up to three additional Z-Wave groups, which are associated with this device. Tipping one time or two times the switching paddle performs the control. The left paddle controls the local load while the right paddle remotely controls Z-Wave associated devices only. The association of further Z-Wave devices needs to be done by a Z-Wave controller. The unit is powered by 230V power and needs a pattress box with 230 V power wires for installation. The unit is shipped completely with electronics, switching paddle and mounting frame in arctic white HomePro style. The mounting frame can be replaced by another mounting frame of the HomePro switching series. The unit is designed for use within a 3-wire system, which means that a neutral wire (blue) is needed for operations.

Mobile remote control or wall switch? As of now you don't have to decide for one.

With the NodOn wall switch, you can control Z-Wave devices such as lamps, window blinds or switchable sockets directly (stand alone mode). Connected to a smart home gateway it is also possible to activate defined scenes by push of a key.

With the NodOn wall switch, you can control Z-Wave devices such as lamps, window blinds or switchable sockets directly (stand alone mode). Connected to a smart home gateway it is also possible to activate defined scenes by push of a key.

Overflowing bathtubs, leaking washing machines or defects to gas and water pipelines – damages can occur almost anywhere and cause immense costs. The POPP Flow Stop can prevent this – thanks to Z-Wave. Flow Stop is a motor operated shut-off controller for automatic flow stop of gas and water pipes. It is equipped with Z-Wave technology. This means it is particularly suitable for use in smart homes.

Even installation is child’s play. The POPP Flow Stop is delivered completely including valve control/motor, power supply, mounting and Quick Start Guide and is easy to assembly on the existing ball stop valve. In doing so, all usual pipe standards, including ½ ” and ¾“, are possible. On this occasion no pipes must be dismantled or even water must be drained. That way the installation is normally done in 5-10 minutes.

The POPP Flow Stop is driven by a motor and closes the ball valve mechanically. Even though the Motor requires only 12 Volt (1A), it has a high power output as well as high torque, which reliably closes the ball valve in just 10 seconds. Also a manual closing of valve is easily possible in case of power failure – thanks to the clutch release bearing.

Once the Flow Stop is added to a smart home gateway via Z-Wave, the stop valve can be operated via any PC, notebook, smartphone or tablet. Additionally, in the event of leaking gas or water the smart home gateway – when combined with sensors – is able to stop a further inflow automatically and thus protects against more extensive damage and further danger.

The POPP Flow Stop is a good piece of security for the intelligent home defending from nasty surprises and high costs due to gas and water damages.

You want to be informed when it starts raining and your windows are still opened? Or you want to control your garden watering intelligently and you want to note the rainfall as well? The POPP Z-Rain enables this in your Z-Wave Smart Home.

The Z-Rain has an internal rocker, where the rainwater is collected until the weight of the water tilts the rocker. The tilting will be registered from a reed sensor and counted as well. Based on that the rainfall will then be calculated.

With the first tilt of the rocker and therefore right to the beginning of the rain you will receive the first value from the Z-Rain. Then you can get a push-message or E-Mail, if one of your windows is still opened and your awning will close automatically.

The great advantage of the Z-Rain is, that it not only detects rain but also measures the exact amount of rain. A small little shower is not always a reason to close your side windows. You can also configure the value of rain, when you want to be informed about the rain. During a rain fall the Z-Rain reports the amount of rain every 1024 seconds in m3 (total sum of the rainfall), mm per m2 and mm/h (current strength of the rainfall) to the Smart Home Gateway. When the rainfall stops, the last measured value will be sent to the gateway. Afterwards the value will become nil again. With that you can turn off your garden watering with the beginning of a rainfall and turn on the next watering cycle based on the measurements of the last rainfall.

Thanks to Z-Wave and the operation with two standard AAA batteries the Z-Rain can be placed anywhere in your garden. Because of the integrated battery booster technology, the Z-Rain could possibly have lifetime of up to 5 years depending on the wake-Up interval.

StellaZ is a wireless Z-Wave controlled actuator suitable for heating, ventilation and air conditioning systems.

Sensor, controller and actuator are combined in a single device to allow a self-sufficient energy-efficient room control.

The device has four different modes (Normal, Energy saving, Frost protection, direct valve control via Z-Wave) to control and regulate the temperature. It is also possible to readout the temperature via wireless Z-Wave requests.

Open windows are automatically detected and lead to a temporary reduction of the heating power to save energy.