Fabricante: X10

Dimming actuator

Se el primero en opinar sobre este producto

€36,58 sin IVA

The LW12 is an in-wall module with built-in dimmer that can be installed behind existing momentary switches or wall outlets.

The LW12 can be controlled with X10 signals via the mains or a momentary switch connected to the LW12. The LW12 has a memory setting for the last dimmer setting and uses SoftStart and SoftDim. The LW12 is the only X10 module that doesn't use a zero wire. This means it can replace a switch without having to use any extra wiring.

The AW 12 reacts to the standard X10 commands that are: "All Units On", "All Units Off", "All Lights Off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On" an "Off" commands.

House code and unit code are programmed using any X10 compatible controllers. There is an EEPROM that stores the house and unit code even when the power is cut.

SKU: LW12

Ship to

Shipping Method

Name

Estimated Delivery

Price

No shipping options

Disponibilidad: Agotado

Cantidad:

Overview
reseñas
Contáctenos

Features:

Memory function for last dimmer setting:
Soft dimming and brighten;
Can be programmed to receive group commands (e.g. All Units Off);
Compatible with all X-10 devices.

TechInfo:

Supply voltage: 230V +/- 10% 50Hz;
Power consumption: <1 W;
Maximum load: 250W (can be slightly lower if using halogen lamps with electronic transformer);
Ambient temperature: -10C to +40C;
Dimensions: 46mm x 46mm x 17mm.

Escriba su propia opinion

Solo los usuarios registrados pueden agregar sus comentarios

Su nombre *

Su correo electronico *

Subject: *

Consulta *

Features:

Memory function for last dimmer setting:
Soft dimming and brighten;
Can be programmed to receive group commands (e.g. All Units Off);
Compatible with all X-10 devices.

TechInfo:

Supply voltage: 230V +/- 10% 50Hz;
Power consumption: <1 W;
Maximum load: 250W (can be slightly lower if using halogen lamps with electronic transformer);
Ambient temperature: -10C to +40C;
Dimensions: 46mm x 46mm x 17mm.

Los clientes que compraron este producto tambien han comprado

Universal Alarm Interface

SM10E

€36,58 sin IVA

Connects to an existing system and turns on lights when tripped. It has 3 modes of operation:
In mode 1 the SM10 will turn On all Lamp Modules and Wall Switch Modules set to its House code, and will also turn On any other Modules set to its Unit code, a stereo connected to an Appliance Module, for example. All Lamp Modules and Wall Switch Module are left in the On state when the system is deactivated, but the Module set to the same Unit code as the SM10 will turn Off.
In mode 2 the SM10 will FLASH all lights connected to Lamp Modules or Wall Switch Modules. All Lamp and Wall Switch Modules will be left in the On state when the system is de-activated but Appliance modules set to the same House code as the SM10 will turn Off.
In mode 3 the SM10 will turn ON any Module set to the same House Code and Unit Code as the SM10 when the system is activated and turns it OFF when the input contact is opened.
Set the input switch to A for triggering the interface by a low voltage input (6-8 V AC, DC or audio), to B for triggering the interface by a dry contact closure. Do not connect 220V to the input terminal!
The SM10 has a test button which allows you to activate it whether or not it is connected to a system. The All light off button allows you to turn off anything which has been turned on by the interface.
To install the SM10 (is expected to be installed inside the security controller panel) :
• Connect the system output to the screw terminals.
• Connect the flying lead to the 230V power supply, most likely at the 230V side of the transformer.

PowerHorn Siren

PH7208

€58,56 sin IVA

PowerHorn is used as an additional audio alarm unit for use with the Home Security System which gives an additional independent 110 decibel sound output when the security system is triggered. The PowerHorn will only trip a few seconds later after the alarm trips. It counts the sequence transmitted to flash lights connected to Lamp Modules after the lights have flashed 4 or 5 times. This prevents it from being accidentally tripped from any other X10 controller.
You can also trip the PowerHorn from any other X10 controller, which is useful in panic situations.
It can be added anywhere around the home; nobody wants to hang around when one of these activate.