Close
(0) artículos
No tiene articulos en su carrito de compras.
TODAS LAS CATEGORIAS
    Filters
    Preferencias
    Buscar

    PowerHorn Siren

    €72,03 IVA incluido
    PowerHorn is used as an additional audio alarm unit for use with the Home Security System which gives an additional independent 110 decibel sound output when the security system is triggered. The PowerHorn will only trip a few seconds later after the alarm trips. It counts the sequence transmitted to flash lights connected to Lamp Modules after the lights have flashed 4 or 5 times. This prevents it from being accidentally tripped from any other X10 controller.
    You can also trip the PowerHorn from any other X10 controller, which is useful in panic situations.
    It can be added anywhere around the home; nobody wants to hang around when one of these activate.
    SKU: PH7208
    Ship to
    *
    *
    Shipping Method
    Name
    Estimated Delivery
    Price
    No shipping options





    TechInfo: Power: 230V, 50 Hz
    Current: <= 20 mA capacitive
    Sound Output: 110 dB
    Signal Sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
    Input Impedance: <= 55 ohm (L-N) at 12 kHz
    Temperature: -10°C to 50°C (operation); - 20°C to 70°C (storage)
    Dimensions: 53 x 123 x 33 mm
    EMC Emission: according to EN 80081-1
    EMC Immunity: according to EN 680082-1
    Electrical Safety: according to EN 60950 and EN 60065







    Escriba su propia opinion
    • Solo los usuarios registrados pueden agregar sus comentarios
    *
    *
    • Malo
    • Excelente
    *
    *
    *
    *





    TechInfo: Power: 230V, 50 Hz
    Current: <= 20 mA capacitive
    Sound Output: 110 dB
    Signal Sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
    Input Impedance: <= 55 ohm (L-N) at 12 kHz
    Temperature: -10°C to 50°C (operation); - 20°C to 70°C (storage)
    Dimensions: 53 x 123 x 33 mm
    EMC Emission: according to EN 80081-1
    EMC Immunity: according to EN 680082-1
    Electrical Safety: according to EN 60950 and EN 60065







    Los clientes que compraron este producto tambien han comprado

    Dimming actuator (reacondicionado)

    LW12
    €30,14 IVA incluido
    The LW12 is an in-wall module with built-in dimmer that can be installed behind existing momentary switches or wall outlets.

    The LW12 can be controlled with X10 signals via the mains or a momentary switch connected to the LW12. The LW12 has a memory setting for the last dimmer setting and uses SoftStart and SoftDim. The LW12 is the only X10 module that doesn't use a zero wire. This means it can replace a switch without having to use any extra wiring.

    The AW 12 reacts to the standard X10 commands that are: "All Units On", "All Units Off", "All Lights Off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On" an "Off" commands.

    House code and unit code are programmed using any X10 compatible controllers. There is an EEPROM that stores the house and unit code even when the power is cut.

    Nos gustaría señalar que este artículo no es un producto nuevo. El producto tiene la funcionalidad completa y se puede utilizar sin restricciones. No obstante, el producto puede tener las siguientes características:

    sello roto,
    embalaje dañado,
    sin embalaje original
    faltan accesorios,
    mínimos signos de desgaste,
    sin versión de software actual.

    Ofrecemos una garantía de un año. Con una posible devolución, recibe una nota de crédito, no hay cambio del producto. La imagen puede no corresponder con el alcance de la entrega del producto.
    Disponibilidad: Agotado

    Universal Alarm Interface

    SM10E
    €44,99 IVA incluido
    Connects to an existing system and turns on lights when tripped. It has 3 modes of operation:
    In mode 1 the SM10 will turn On all Lamp Modules and Wall Switch Modules set to its House code, and will also turn On any other Modules set to its Unit code, a stereo connected to an Appliance Module, for example. All Lamp Modules and Wall Switch Module are left in the On state when the system is deactivated, but the Module set to the same Unit code as the SM10 will turn Off.
    In mode 2 the SM10 will FLASH all lights connected to Lamp Modules or Wall Switch Modules. All Lamp and Wall Switch Modules will be left in the On state when the system is de-activated but Appliance modules set to the same House code as the SM10 will turn Off.
    In mode 3 the SM10 will turn ON any Module set to the same House Code and Unit Code as the SM10 when the system is activated and turns it OFF when the input contact is opened.
    Set the input switch to A for triggering the interface by a low voltage input (6-8 V AC, DC or audio), to B for triggering the interface by a dry contact closure. Do not connect 220V to the input terminal!
    The SM10 has a test button which allows you to activate it whether or not it is connected to a system. The All light off button allows you to turn off anything which has been turned on by the interface.
    To install the SM10 (is expected to be installed inside the security controller panel) :
    • Connect the system output to the screw terminals.
    • Connect the flying lead to the 230V power supply, most likely at the 230V side of the transformer.

    Hub II Insteon - Plug In Edition

    INS 2245-422
    €119,99 IVA incluido
    The Insteon Hub II allows you to control your home through any smartphone, tablet or aplle watch.
    The Hub works in conjunction with your hhome routerrouter, smartphone or tablet, to monitor Insteon devices installed in your home. The Insteon for Hub app is available for Android and IOS for free!
    Create multiple scenes, easily configurable in Hub II and create alerts by adding water leak detectors, motion detectors, door / window detectors, etc. Integrate your Sonos easily and control the sound system of your home by the Insteon app. br> The Hub II works with Amazon Alexa, a voice control interface and it´s a compatible with Stringify App.
    Disponibilidad: En existencia