Close
(0) items
You have no items in your shopping cart.
All Categories
    Filters
    Preferences
    Search
    Manufacturer: X10

    DIN Rail Switch

    €48.37 excl tax
    EOL equipment:
    Alternatives:
    INS_2453-422 Din rail actuator
    AW12 + Din Enclosure

    The X10 DIN rail switch is a remote controlled relay. Discretely installed at the junction box, it switches hard-wired circuits with several switches (e.g. hallway lighting). The internal relay can be tripped either by external latched or momentary action wall switches or by an X10 controller.

    The AD10E responds to STANDARD X10 protocols: "All units off" from any X10 controller set to its house code, regardless of unit code. Or alternatively, by individual unit control using "On" and "Off". When the relay is energized, the LED above the slide switch is illuminated.

    SKU: AD11

    Features:

    • Position 0: the connected load is switched off permanently and cannot be switched on by the wall switches or an X10 controller.
    • Position 1: the connected load is switched on permanently and cannot be switched off by the wall switches or an X10 controller.
    • Position auto: the connected load can be switched by the wall switches or an X10 controller.
    • Terminal 1 is designed for toggle switches: the relay picks up when phase is present and releases when there is no voltage at the terminal.
    • Terminal 2 is designed for pulse contacts: each time phase is applied to the relay switches.

    Application:

    This unit can replace any pulse contact relay that is commonly used for multi-switched hall and entry lighting. In discrete locations, e.g. kitchen lighting, you may prefer to install the AD10E in a small sub-junction box.

    TechInfo:

    • Supply voltage: 230V +10% -15% 50 Hz
    • Supply current : = 20 mA capacitive
    • Making capacity:
      • 3600 W (resistive)
      • 3 A (motors)
      • 16 A (resistive loads)
    • EMC emission: according to EN 50081-1
    • EMC immunity: according to EN 50082-1
    • Electrical safety: according to EN 60950 and EN 60065
    • Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
    • Input impedance: = 180 Ohms (L - N) at 120 kHz
    • Connections: screw type terminals for phase, neutral, switched phase, control 1 and 2.
    • Ambient temperature:
      • - 10° C to + 40° C (operation)
      • - 20° C to + 70° C (storage)

    Warning: For professional use! When installing consult an electrician.





    Write your own review
    • Only registered users can write reviews
    • Bad
    • Excellent

    Features:

    • Position 0: the connected load is switched off permanently and cannot be switched on by the wall switches or an X10 controller.
    • Position 1: the connected load is switched on permanently and cannot be switched off by the wall switches or an X10 controller.
    • Position auto: the connected load can be switched by the wall switches or an X10 controller.
    • Terminal 1 is designed for toggle switches: the relay picks up when phase is present and releases when there is no voltage at the terminal.
    • Terminal 2 is designed for pulse contacts: each time phase is applied to the relay switches.

    Application:

    This unit can replace any pulse contact relay that is commonly used for multi-switched hall and entry lighting. In discrete locations, e.g. kitchen lighting, you may prefer to install the AD10E in a small sub-junction box.

    TechInfo:

    • Supply voltage: 230V +10% -15% 50 Hz
    • Supply current : = 20 mA capacitive
    • Making capacity:
      • 3600 W (resistive)
      • 3 A (motors)
      • 16 A (resistive loads)
    • EMC emission: according to EN 50081-1
    • EMC immunity: according to EN 50082-1
    • Electrical safety: according to EN 60950 and EN 60065
    • Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
    • Input impedance: = 180 Ohms (L - N) at 120 kHz
    • Connections: screw type terminals for phase, neutral, switched phase, control 1 and 2.
    • Ambient temperature:
      • - 10° C to + 40° C (operation)
      • - 20° C to + 70° C (storage)

    Warning: For professional use! When installing consult an electrician.