Flush shutter DC module with inverting power polarity is used to control the 12-24VDC motor of blinds, rollers, shades, venetian blinds, windows, etc.

New functionality - support venetian blind slats tilting

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

This module is used for switching On or Off 1 electrical device like light, fan, oven, washing machine, iron, power socket, garage door, electric radiator, water heater, etc.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

This module is used for switching On or Off 1 electrical device like light, fan, oven, washing machine, iron, power socket, garage door, electric radiator, water heater, etc.

With this module can feed your load with the desired voltage because it has a separate entrance for this purpose.
item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

Discrete Z-Wave Flush PWM thermostat allows you to control radiant floor or radiators with PWM valves.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

Discrete Z-Wave Flush heat & cool thermostat allows you to control 4 pipes fan coil or cooling beam with your smartphone.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

The Z-Wave module can be used to directly control an electrical or water floor heating system, electric water heater, hot water pump, electrical radiator, etc.

Incredible sensor temperature range
Temperature sensor measures temperature from -50.0°C to +125.0°C, with a 0.1°C resolution.

No batteries required – Connect direct to any heating device
As it is connected directly to either 230VAC or 24VDC, no batteries are required.

Hidden thermostat - clean walls
There is no need to have big room thermostat on the wall, because the temperature set point is set through a Z-Wave network.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

The Qubino On/Off Thermostat 2 is your wireless heating and hot water controller that also measures the power consumption. This amazingly tiny module is ideal for wireless control of electric or water-based underfloor heating systems, electric water heaters, hot water pumps, and electric radiators.

5 x QUBINO insert modules of your choice:
ZWGOA ZMNHDD1 – Flush Dimmer Z-Wave Plus
ZWGOA ZMNHBD1 -Flush 2 Relays Z-Wave Plus
ZWGOA ZMNHAD1– Flush 1 Relay Z-Wave Plus
ZWGOA ZMNHCD1 - Flush Shutter Z-Wave Plus

Note: In the observation field please define the references and quantities of your choice.

This Z-Wave module is used for energy measurements in single-phase electrical power network till 65A. Meters measure energy directly in 2-wire networks according to the principle of fast sampling of voltage and current signals. A built-in microprocessor calculates energy, power and power factor from the measured signals.

The module can be controlled through Z-wave network and it acts as repeater in order to improve range and stability of Z-wave network.

It is designed to be mounted on DIN rail.

item also available in:
908.4 MHz - USA/Canada, México, Chile
921,40 MHz - Australia, Brazil, New Zealand
Contact for details on minimal quantities and deadlines for these frequencies

The Qubino three-phase smart meter can be used in many automation scenarios that make your life more comfortable. Smart Meter is an extremely versatile and powerful instrument for measuring energy in a three-phase power network up to 65A. A built-in microprocessor calculates the power, reactive power and power factor with the measured values. The smart meter is designed to be mounted on a DIN channel. The Qubino Smart Meter can be used in residential, industrial and commercial facilities. This equipment permanently measures the current and voltage in a three-phase network. Calculate the current and total power, the PHI power factor and the reactive energy that is actually consumed. The control through Z-Wave allows to act the relays (available separately), as well as to evaluate the results of the measurements of the device. With the energy data we can carry out the most varied actions, such as being alerted if the consumption exceeds a certain limit, sliding loads to keep the consumption below a certain level, etc.

to work with ZWGOA ZMNHTD1 Smart Meter
wired connection
Voltage: 230V ± 10%, 50-60Hz
Current: 32A, 2 pole

to work with ZWGOA ZMNHTD1 Smart Meter
Infra-red connection
Voltage: 230V ± 10%, 50-60Hz
Current: 32A, 4 pole

Temperature sensor can be installed inside this Wall mounted casing. The dimensions of the Wall mounted casing are 71mm x 71mm x 27mm. This casings are made from ABS material and are available in white colour.

Temperature sensor can be installed behind this 2M casing SET. It is suitable for mounting on boxes Ø60 with claws. SET consists of: 1 x cover plate1, 2 x 1M perforated blank cover and 1 x mounting frame 2M with claws. 2M casing SET is made of PC/ABS material and comes in 2M dimensions. 2M casing set is available in polar white colour.

Digital Temperature sensor has 1m cable with connector to connect directly to the different modules. The digital temperature sensor range is between -50°C and +125°C.

Din rail enclosure that can be used to mount Fibaro modules on DIN rails.

Expander for CMEB box.
It fits on the side of the CMEB and it makes it 17,5mm wider and adds 8 terminals.

SPU-DIM-C02 can control single colour LED strips from a standard push switch or from a 0-10V or 1-10V from any manufacturer. The controller can be connected to one or more push switches (check wiring diagram) or with 0-10V or 1-10V signals