Close
(0) items
You have no items in your shopping cart.
All Categories
    Filters
    Preferences
    Search
    Manufacturer: Heatit

    Z-TRM3 electronic thermostat

    €146.37 incl tax
    Heatit Z-TRM3 is an electronic thermostat for electrical floor heating, designed to be mounted in a standard flush box. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems. Heatit Z-TRM3 has SmartStart. This feature allows the user to include all devices with SmartStart by scanning the QR codes on the devices. On startup all the devices will automatically be included in the gateway (requires SmartStart compability). This saves the installer a lot of work.

    Art. 54 305 99
    SKU: 54 305 99
    Delivery date: It will be available in 1st quarter 2020

    Heatit Z-TRM3 is equipped with a single pole switch and fits into System 55 frames. The thermostat can withstand a load of max 16A /3600W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors. The thermostat has the capacity of up to 8 associations (relays, wall plugs etc.). 

    The thermostat is designed for electrical heating. It may be used for waterbased heating if the thermostat is linked with the Heatit Z-Water.

    Floor sensor
    Internal room sensor
    External room sensor (connected by cable)
    Temperature limiter
    SmartStart
    Weekly program/ setback via gateway
    Temperature read out in gateway
    Firmware update (OTA)
    Power metering
    Relay status LED
    Single pole switch
    Lock mode/child lock
    Calibration
    8 associations
    Supports encryption mode: S0, S2 Authenticated Class, S2 Unauthenticated Class


    This product is a security-enabled Z-Wave Plus product with encryption. The product must be used with a security-enabled Z-Wave Controller in order to fully utilize the product

    TECHNICAL DATA

    Protocol Z-Wave - 868,4MHz
    Chip
    Z-Wave 500 chip
    Rated voltage 230V 50/60Hz
    Max load 3600W (resistive load) 750W self-limiting heating cable
    Max current 16A
    Power consumption <2,0W
    Ambient temperature 0°C to 40°C (during operation)
    Temperature range 5°C to 40°C
    Hysteresis 0,3°C to 3,0°C (default 0,5°C)
    Compatible with NTC  
    sensors with values 10, 12, 15, 22, 33 and 47 kΩ @ 25°C
    IP Code IP 21
    Approvals Z-Wave Plus, CE, EN 60730-1, EN 60730-2-9, EMC 2014/30/EU, RoHS 2011/65/EU, LVD 2014/35/EU
    Approved for use in bathrooms
    Use wires 1,5mm² or 2,5mm² according to load
    The product is maintenance-free, but must not be covered

     

    Acessories:

    • Plastic kit for Heatit (front and frame)
    • Floor sensor Ø 4mm 3 meters NTC 10 kΩ
    • Floor sensor Ø 4mm 6 meters NTC 10 kΩ
    • External enclosed sensor IP 20/54 NTC 10 kΩ
    Write your own review
    • Only registered users can write reviews
    • Bad
    • Excellent

    Heatit Z-TRM3 is equipped with a single pole switch and fits into System 55 frames. The thermostat can withstand a load of max 16A /3600W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors. The thermostat has the capacity of up to 8 associations (relays, wall plugs etc.). 

    The thermostat is designed for electrical heating. It may be used for waterbased heating if the thermostat is linked with the Heatit Z-Water.

    Floor sensor
    Internal room sensor
    External room sensor (connected by cable)
    Temperature limiter
    SmartStart
    Weekly program/ setback via gateway
    Temperature read out in gateway
    Firmware update (OTA)
    Power metering
    Relay status LED
    Single pole switch
    Lock mode/child lock
    Calibration
    8 associations
    Supports encryption mode: S0, S2 Authenticated Class, S2 Unauthenticated Class


    This product is a security-enabled Z-Wave Plus product with encryption. The product must be used with a security-enabled Z-Wave Controller in order to fully utilize the product

    TECHNICAL DATA

    Protocol Z-Wave - 868,4MHz
    Chip
    Z-Wave 500 chip
    Rated voltage 230V 50/60Hz
    Max load 3600W (resistive load) 750W self-limiting heating cable
    Max current 16A
    Power consumption <2,0W
    Ambient temperature 0°C to 40°C (during operation)
    Temperature range 5°C to 40°C
    Hysteresis 0,3°C to 3,0°C (default 0,5°C)
    Compatible with NTC  
    sensors with values 10, 12, 15, 22, 33 and 47 kΩ @ 25°C
    IP Code IP 21
    Approvals Z-Wave Plus, CE, EN 60730-1, EN 60730-2-9, EMC 2014/30/EU, RoHS 2011/65/EU, LVD 2014/35/EU
    Approved for use in bathrooms
    Use wires 1,5mm² or 2,5mm² according to load
    The product is maintenance-free, but must not be covered

     

    Acessories:

    • Plastic kit for Heatit (front and frame)
    • Floor sensor Ø 4mm 3 meters NTC 10 kΩ
    • Floor sensor Ø 4mm 6 meters NTC 10 kΩ
    • External enclosed sensor IP 20/54 NTC 10 kΩ